Do You Have To Register Your Otterbox Case

Download Article

Otterboxes are some of the most durable smartphone and tablet cases you can buy—but that same durability can make it difficult to remove from your device. If you know which type of case you have, you can use different tips and tricks to pry them off carefully without damaging your phone or tablet. With a little bit of patience and some elbow grease, you can get your case off quickly without a ton of frustration.

1
Remove the snap-on holster. If the device is in a belt clip or other snap-on attachment, pop it off using the large tab on the side. This will make it much easier to take the rest of the case off, so it's best to do it right away.^[1]
- The process for removing a Defender Otterbox case will be the same for virtually all devices (iPhone, Android, etc.). The only differences will be the number and the style of tension clips.
2
Find an opening in the silicone slipcover. The most difficult part of removing the Defender case is peeling off the flexible silicone layer. Your best bet is to start at the camera opening, the charging port, or a corner of the screen.^[2]
- The silicone cover is the flexible outer layer of the case, not the hard plastic inside.
3
Wedge a thin tool or your finger under the cover. Use the tip of your finger to pry the silicone cover away from your phone. If you can't fit your finger into one of these openings, use an old credit card or a coin to help you out. Stick it underneath the slipcover, and wiggle it back and forth until you can insert your finger into the gap.^[3]
- Make sure you're not using a credit card you still use! If you wiggle too hard or too fast, your card could accidentally snap.
4

Peel the silicone off carefully. Once you've wedged a corner open, you should be able to go around the phone pulling off the silicone. Be careful when removing the silicone from your open ports to avoid tearing any port covers.^[4]
5
Release the tension clips along the edge of the case. Feel along the edge of the case and find the small clips along your phone. Use your fingers to pop the clips up one by one until the 2 sides separate and fall off your device.^[5]
- If you can't get your finger under the clip, you may need to use a small flat-head screwdriver or a stiff credit card to get some leverage.
- If you're using a tool to pry the clips open, lift towards the front of the case. Don't try to pull down, or you may break the plastic.
- Some clips may be easier to remove than others, especially when all clips are closed. If you're having trouble with one, move onto a different clip.

1

Start at the top of the device. You'll have the easiest time removing the plastic part of the case if you work from the top of the device. Grab one of the corners on the top edges above the front camera with the phone facing toward you.^[6]
2
Pull the top plastic up and off the rubber. You may have to lift a bit to get the plastic over any Power buttons. When you lift the plastic top off, the rest of the case should come off easily.^[7]
- If you have any trouble, try pushing a coin or a credit card underneath the rubber case.
3

Push the rubber casing off one of the corners with your thumb. Starting from the corner is the easiest way to begin removing the rubber. The seal will be tight, so you'll need to push with some force.^[8]
4
Work the rubber casing off of the device. Be careful with the ports, as the rubber port covers can tear easily. Once the rubber is off your device, you're in the clear.^[9]
- Try storing your case somewhere it won't collect dust.

1
Push the case off one of the corners with your thumb. The Symmetry series is one of Otterbox's simplest cases: a flexible silicone enclosure for your phone. The seal is tight, so you'll have the best luck starting from a corner and pushing the case off the edge.^[10]
- Otterbox recommends starting at the top edge.
2
Use a hard plastic card if necessary. Wedge the card under an edge of the flexible case. Lever it back and forth to pry the case away from the device enough to grasp it with your finger.^[11]
- You can try this if using your hands doesn't work.
3

Work your way around the case. Once you have a corner off, you can work your way around the edge of the case to remove it. Be careful with the port covers so that they don't get torn.^[12]

1
Open up the iPad case. You can do this by flipping it open like you would to use your iPad. Spread the case out flat so that it's easier to work with.^[13]
- If you have a keyboard connected to your iPad, pop that off first before you start.
2
Press down on one bottom corner. This will start to remove the case from the edges of your iPad. As you press down, try to pull your iPad up by the corner at the same time.^[14]
- If you're having trouble, try sticking a coin in between the case and the iPad.
3

Pull your iPad up and out of the case. Once you have one corner free, pull your iPad up and away from the case. If any of the corners get stuck, carefully wiggle them out before you keep lifting.^[15]

Add New Question

Question

Do you need to remove the plastic cover from the front of the otterbox case?

Some models have a screen cover built into the case, while others have a plastic sheet that attaches directly to the screen before the case is installed. Either way, you do not need to remove the cover to open the otterbox case.
Question

How do I remove an Otterbox from my iPhone 6?

On the side, there should be a clasp or something to detach the two part of the phone case. Next, you can use your nails or anything strong and thin (like a credit card) to take them apart.
Question

How do I open the Otter Box for an HTC Desire Eye?

This is one of the Defender cases described above. It helps to have a hard plastic card to wedge under the flexible cover. If the snaps on the hard inner shell won't open, you can carefully pry them apart with a butter knife or flat head screwdriver.
Question

How do I remove the otter case from a Samsung Galaxy 7?

Try opening all port covers before removing the flexible case. There are Defender, Commuter, and Symmetry cases available for the Galaxy 7, so if you're not sure which you have, try all the methods above.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Some Otterbox cases come with a hard plastic tool to help you wedge open the two halves of the case. This tool is designed to slip onto the lanyard on your case. If you don't have this tool, a hard plastic library card or similar tool should work.

Thanks for submitting a tip for review!

About This Article

Article Summary X

To open an Otterbox Case for the Defender Series, start by popping the snap-on holster off using the large tab on the side. Once the holster is off, find an opening in the silicone slipcover near the camera opening, charging port, or a corner of the screen. If you can't fit your fingers into any of the openings, use an old credit card or other hard, flexible piece of plastic to slip under the cover. Wiggle your credit card under the plastic until you can fit a finger into the gap. After you wedge a corner open, start prying off the silicone. When the silicone is off, find the tension clips along the edge of the case, and pop them open with your fingers. Continue to release the tension clips until the 2 halves separate. To learn how to remove an Otterbox Case from an iPad, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 721,814 times.